Recent Content by matib12

  1. matib12
    Post

    Interrupt on udoo

    I've tried few weeks ago the sketch I posted before. It counted approx. 65000 pulses than hang-up again... If I have time I'll retry this week.
    Post by: matib12, Oct 26, 2016 in forum: Arduino IDE
  2. matib12
    Post

    Interrupt on udoo

    @ektor5 The result of ls /proc/device-tree/soc/aips-bus@02000000/*/m4-reserved-pin is as you predicted. On the other hand I modify the device tree...
    Post by: matib12, Jul 28, 2016 in forum: Arduino IDE
  3. matib12
    Post

    Interrupt on udoo

    My uname -a gives: The kernel is a recompiled from the git source and default configuration but without MCC support. Thanks to @ektor5 for...
    Post by: matib12, Jul 28, 2016 in forum: Arduino IDE
  4. matib12
    Post

    Interrupt on udoo

    I confirm the issue. I described it in my previous post. I've found the problem on my board which doesn't have problems with IO ports.
    Post by: matib12, Jul 28, 2016 in forum: Arduino IDE
  5. matib12
    Post

    Known Neo Arduino problems overview

    My solution for MCC is shared memory between cores. I recompile each time new kernel without MCC (it would be nice to have it built as a module)....
    Post by: matib12, Jul 25, 2016 in forum: UDOO NEO
  6. matib12
    Post

    Interrupt on udoo

    I'm using cross-compilation. Today I updated BSP of my Arduino IDE. I obtained much better result. Below I paste working piece of the PPM decoder....
    Post by: matib12, Jul 23, 2016 in forum: Arduino IDE
  7. matib12
    Post

    Interrupt on udoo

    @waltervl I made the test with a fresh udoobuntu-udoo-neo-desktop_2.0rc2 immediately updated with apt-get. Then I simply run the software I need....
    Post by: matib12, Jul 22, 2016 in forum: Arduino IDE
  8. matib12
    Post

    Interrupt on udoo

    @Andrea Rovai is sharing *.diff files related to MQX sources a violation of the agreement between UDOO and Freescale?
    Post by: matib12, Jul 14, 2016 in forum: Arduino IDE
  9. matib12
    Post

    Interrupt on udoo

    Hi Nico, Using interrupts to read the state of push button is generally a bad idea because of button bouncing. It means that the button during...
    Post by: matib12, Jul 14, 2016 in forum: Arduino IDE
  10. matib12
    Post

    Interrupt on udoo

    There is no update from MQX 4.1 to 4.2 for UDOOneo processor. Look: https://community.nxp.com/thread/355438. The MQX 4.1 for SoloX is in the...
    Post by: matib12, Jul 13, 2016 in forum: Arduino IDE
  11. matib12
    Post

    Interrupt on udoo

    I see a conflict between creating a project for community and choosing for its realisation a closed source solution. :D
    Post by: matib12, Jul 12, 2016 in forum: Arduino IDE
  12. matib12
    Post

    Interrupt on udoo

    Recently I struggle against the same problem with interrupts. I tried to gather some informations about them. Hardware: Cortex M4 core has its...
    Post by: matib12, Jul 12, 2016 in forum: Arduino IDE
  13. matib12
    Post

    WiFi stopped working

    I confirm that the tests described in my previous post in this topic are sufficient to confirm that the BT/WLAN chip is broken.
    Post by: matib12, Mar 8, 2016 in forum: UDOO NEO
  14. matib12
    Post

    WiFi stopped working

    Hi, I have a problem with WiFi which fits perfectly to the title of this thread. My WiFi stopped working but it was working before. I would say...
    Post by: matib12, Mar 1, 2016 in forum: UDOO NEO
  15. matib12
    Post

    Pin number mismatch

    For those who are eager to fix the problem by their own, you can edit wiring_digital.c file in the board package. First you need to download *.tar...
    Post by: matib12, Feb 24, 2016 in forum: UDOO NEO