Recent Content by SteveD

  1. SteveD
    Post

    Any estimate when firmware 1.03 will be available?

    awesome, a little late for me to mess with it though, at this point I'll have to wait until September to flash it, but I'll be really happy to see...
    Post by: SteveD, Aug 7, 2017 in forum: UDOO X86
  2. SteveD
    Post

    x86 Gallery

    Very Nice, but I do have a question, is this your 3d printed design, or did you order online? Otherwise, wynut just have a mount for the fan in...
    Post by: SteveD, Jul 24, 2017 in forum: UDOO X86
  3. SteveD
    Post

    Udoo x86 hdmi port as input

    Yup just look for a capture card or usb capture device. Real shame these don't exist, integrated, I would love to plug my pi, or my udoo into my...
    Post by: SteveD, Jul 24, 2017 in forum: UDOO X86
  4. SteveD
    Post

    Hot UDOOx86 + Ubuntu 16.04

    I've got an advanced running Ubuntu Mate 24/7, running a desktop application, server/seedbox. Mine is set to turn on the fan at 55C, and it...
    Post by: SteveD, Jul 18, 2017 in forum: UDOO X86
  5. SteveD
    Post

    Where Do I Start?

    Yeah I saw your previous post and I think I stumbled across that same one. What I can say is that the retropie images are much more optimized...
    Post by: SteveD, Jul 18, 2017 in forum: UDOO X86
  6. SteveD
    Post

    Questions about a Udoo X86 as a USB hifi transport

    I run my advanced as a 24/7 server / seedbox, the heatsink does get warm, but rarely up to 55C to turn on my fan. Your headless setup should run...
    Post by: SteveD, Jul 18, 2017 in forum: UDOO X86
  7. SteveD
    Post

    Any estimate when firmware 1.03 will be available?

    I don't mean to prod, but also anticipating the firmware update. I've got some big plans for automation in the future, I was going to deal within...
    Post by: SteveD, Jul 14, 2017 in forum: UDOO X86
  8. SteveD
    Post

    Udoo x86 don't recognizes sata ports

    Post by: SteveD, Jul 14, 2017 in forum: UDOO X86
  9. SteveD
    Post

    Best WebCamera for X86

    I had a very similar camera from logitech, must be 6-7 years old now, if I remember correctly in performed well except for low light.
    Post by: SteveD, Jul 7, 2017 in forum: UDOO X86
  10. SteveD
    Post

    Alternative fan, quiet and far better performance

    I think you're taking the initial post too litterally. Example, if I said my board was getting hot, what I really mean is the processor with the...
    Post by: SteveD, Jul 7, 2017 in forum: UDOO X86
  11. SteveD
    Post

    Alternative fan, quiet and far better performance

    very nice, I prefer your DC jack breakout connector, I was planning a similar solution for my diy nas, to power usb hub/sbc. Then a 2 second mis...
    Post by: SteveD, Jun 28, 2017 in forum: UDOO X86
  12. SteveD
    Post

    Obvious battery flaw

    like firstgengeek said, just use double sided sticky tape. if you're worried about shorting any connections use electrical tape to cover the...
    Post by: SteveD, Jun 27, 2017 in forum: UDOO X86
  13. SteveD
    Post

    CPU fan does not turn on (Solved)

    I missed there was a setting for which type of fan is used, currently I've got a 2pin, but it never turns on after boot, I reduced the AC(0?) down...
    Post by: SteveD, Jun 21, 2017 in forum: UDOO X86
  14. SteveD
    Post

    M.2 SSD (not NVME) 2280 (not 2260) deal

    Yeah take your two cents back, they're not wanted, this isn't 'Merica, its a forum! Your opinion is quite valued though, I completely agree...
    Post by: SteveD, Jun 21, 2017 in forum: UDOO X86
  15. SteveD
    Post

    CPU Fan

    Hey Nice, I would have just opted to go with the arduino pins. Editing the bios sounds a few levels above me, but did you change an entry, or the...
    Post by: SteveD, Jun 19, 2017 in forum: UDOO X86