Linux Quad SD not working after update

Hi,
I'm new at UDOO just starting today with the udoo board
I try to update the linux Quad SD following the guide:
http://www.udoo.org/update-procedure/

I try the online method after complete all steps and reboot the udoo board the system it's not running,
The only screen I see is like this:

The UDOO Logo and in the right hand:
u-boot-imx-2013-10 on:
UDOO Board 2013
CPU Freescale i.MX6 Quad/Dual 1Ghz
qual/dual ARMv7 Cortex-A9 core
1 GB RAM DDR3
Vivante GC2000 / GC880
Atmel SAM3X8E ARM Cortex-M3 CPU
Ardruino-compatible R3 1.0 pinout

I wait around 1h minutes with the same screen, I tried to restart, disconnect all connect again, I tested the Ardruino SM and works fine.
Can you help me to solve the problem ??

Thanks

 

Hi,

Try to connect to Udoo serial debug port , then post the output and We try to solve your problem.

 

Hi, thanks for the reply

I didn't know the debug port, nice to know
This is my output: ERROR: can't get kernel image!

Code:

U-Boot 2013.10-rc3-svn109 (Nov 27 2013 - 17:36:22)
CPU:   Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: UDOO
DRAM:  1 GiB
MMC:   FSL_SDHC: 0
auto-detected panel HDMI
Display: HDMI (1024x768)
In:    serial
Out:   serial
Err:   serial
Net:   using phy at 6
FEC
Hit any key to stop autoboot:  3  2  1  0 
MMC Device 2 not found
no mmc device at slot 2
MMC Device 2 not found
** Bad device mmc 2 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!

 

Yes,

I think the same, uboot can't find kernel image to load into memory!

 

Hi,

I've found this happened to me after the update. I'm not sure why it happened, but essentially the mmc device location changes from device 2 to device 0. This can be checked at uboot with the mmc command. In order to fix:

1. reset, halt boot in uboot.

2. Lets confirm the mmc card is device 0..

Code:

UDOO board => mmc list
FSL_SDHC: 0

UDOO board => mmc dev 0
mmc0 is current device

UDOO board => mmcinfo
Device: FSL_SDHC
Manufacturer ID: 82
OEM: 4a54
Name: NCard
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 14.7 GiB
Bus Width: 4-bit

3. All good, we know it's device 0. Let's configure the boot device and commit the changes to the MMC card.

Code:

setenv bootdev "mmc dev 0; ext2load mmc 0:1"
saveenv

Saving Environment to MMC...
Writing to MMC(0)... done

4. Boot the monster..

Code:

UDOO board => boot
mmc0 is current device
4120128 bytes read in 328 ms (12 MiB/s)
## Booting kernel from Legacy Image at 10800000 ...
   Image Name:   Linux-3.0.35
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4120064 Bytes = 3.9 MiB
   Load Address: 10008000
   Entry Point:  10008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...