Search Results

Search Again
Page 3 of 10
  1. waltervl
    Post

    Barometer Brick example not working?

    This could give some hints: https://petermolnar.net/linux-i2c-iio-collectd/
    Post by: waltervl, Sep 13, 2019 in forum: UDOO NEO
  2. waltervl
    Post

    Barometer Brick example not working?

    @Girija Are you using this with a Udoo Neo on a Udoobuntu operating system?
    Post by: waltervl, Sep 12, 2019 in forum: UDOO NEO
  3. waltervl
    Post

    Faulty CN9 USB-C connector/port?

    I would advise you to go straight to Udoo customer care and raise a ticket: https://ticket.udoo.org/
    Post by: waltervl, Sep 10, 2019 in forum: UDOO BOLT
  4. waltervl
    Post

    udoo bolt + ubuntu

    Did you use the "nomode" parameter in grub during setup as indicated in the documentation you mentioned?
    Post by: waltervl, Sep 9, 2019 in forum: UDOO BOLT
  5. waltervl
    Post

    Wrong gpio numbers

    Could it be you are on an older Kernel? Kernel < 4.15 eg ubuntu < 18.04, https://en.wikipedia.org/wiki/Ubuntu_version_history#Table_of_versions...
    Post by: waltervl, Sep 6, 2019 in forum: UDOO X86
  6. waltervl
    Post

    Gpio Pins Value on Startup

    You can do that in the same script but only for output GPIO. After you have exported them as output you can set them high or low to your wishes....
    Post by: waltervl, Sep 5, 2019 in forum: UDOO X86
  7. waltervl
    Post

    Gpio Pins Value on Startup

    Thanks. Would be nice if share your changes for future reference.....
    Post by: waltervl, Sep 5, 2019 in forum: UDOO X86
  8. waltervl
    Post

    Bolt v8 Doesn't Boot

    USB-C power source is also known source of not booting of the Udoo Bolt, at least on the first times.. Try one of the compatible ones, best is to...
    Post by: waltervl, Sep 3, 2019 in forum: UDOO BOLT
  9. waltervl
    Post

    HDMI is not working in UDOO Quad

    I do not know if you have a normal TV somewhere around where you can attach your Udoo to with a normal HDMI cable? Normally the Udoo Quad will...
    Post by: waltervl, Sep 3, 2019 in forum: UDOO QUAD
  10. waltervl
    Post

    system shutdown

    I would install the OS again, perhaps something went wrong there. Also check the OS logging again for clues.
    Post by: waltervl, Sep 1, 2019 in forum: UDOO BOLT
  11. waltervl
    Post

    Gpio Pins Value on Startup

    2) For the Udoo Quad and Neo the Udoo team made a package in UdooBuntu that exported the GPIO during startup of the board. You could make one...
    Post by: waltervl, Aug 30, 2019 in forum: UDOO X86
  12. waltervl
    Post

    Isnt X86 II just X86?

    They are the same except for the Arduino part (Leonardo instead of 101). BUT there are different versions of the Udoo X86 processors. See also...
    Post by: waltervl, Aug 30, 2019 in forum: UDOO X86
  13. waltervl
    Post

    Is x86 BIOS UEFI ?

    Yes, See https://www.udoo.org/docs-x86/Hardware_Reference/UEFI_Firmware.html [IMG]
    Post by: waltervl, Aug 29, 2019 in forum: UDOO X86
  14. waltervl
    Post

    CentOS 7 install

    Make sure all the prerequisite software packages/libraries are installed before running the script. CENTOS is not installing the same as other...
    Post by: waltervl, Aug 29, 2019 in forum: UDOO X86
  15. waltervl
    Post

    CentOS 7 install

    Preferably do not install an OS on an USB thumb drive for permenant use. Install it on the build in eMMC, or on an external disk through M2 or...
    Post by: waltervl, Aug 28, 2019 in forum: UDOO X86
  16. waltervl
    Post

    Udoo Bolt Dead (Was Working)

    You can contact Udoo Support here by making a support ticket https://ticket.udoo.org/
    Post by: waltervl, Aug 25, 2019 in forum: UDOO BOLT
  17. waltervl
    Post

    Unstable i2c device ID

    I would advise you to drop your question with more technical details (i.e. what levelshifter) in the other I2C discussion thread so the people...
    Post by: waltervl, Aug 23, 2019 in forum: UDOO X86
  18. waltervl
    Post

    Unstable i2c device ID

    If the level shifter is not working correct the I2C communication is not correct resulting in strange behavior. That you can use the levelshifter...
    Post by: waltervl, Aug 22, 2019 in forum: UDOO X86
  19. waltervl
    Post

    Unstable i2c device ID

    No personal experience but try the next thread: https://www.udoo.org/forum/threads/need-help-using-braswell-i2c-with-level-shifter.16269/
    Post by: waltervl, Aug 21, 2019 in forum: UDOO X86
  20. waltervl
    Post

    HDMI is not working in UDOO Quad

    Did you try another cable and/or monitor?
    Post by: waltervl, Aug 21, 2019 in forum: UDOO QUAD
Showing results 41 to 60 of 199 Next >
Search Again
Page 3 of 10